[Estimation of acetabular cup prosthesis coverage rate in total hip arthroplasty based on X-ray films].

Objective: To explore the method of accurately estimating the acetabular cup prosthesis coverage rate (hereinafter referred to as "cup coverage rate") in total hip arthroplasty (THA) based on X-ray films, and to determine the effective parameters that can be used to estimate the cup coverage rate. Methods: The three-dimensional printed pelvic models were established based on CT data of 16 healthy pelvis, and the acetabular prosthesis were implanted according to conventional THA procedure. The length and width of the uncovered area of the acetabular cup prosthesis were measured by a modified X-ray recording method with a rotating C-arm X-ray machine, and the cup coverage rate was calculated. Then the differences among the traditional anteroposterior X-ray recording method, the modified method, and actual measurement on pelvic model were statistically analyzed. The correlation between the area of the uncovered area of the prosthesis and its width and length was analyzed by using multiple linear regression analysis. Results: The cup coverage rates of traditional method, modified method, and actual measurement were 78.22%±3.36%, 86.74%±3.61%, and 89.62%±2.62%, respectively, with significant differences ( P<0.05). The results of multiple linear regression analysis showed that the width and length were positively linear with the uncovered area of the prosthesis, and the regression equation was as follows: uncovered area of the prosthesis=-21.192+0.248×width+0.140×length, and the coefficient of determination R 2=0.857, P<0.001. Conclusion: Compared with the traditional method, the modified method can more accurately evaluate the cup coverage rate during THA, and the width of the uncovered area of the prosthesis can be used as an effective reference for the cup coverage rate.

[Imaging study on determining the rationality of atlantoaxial fixation angle based on the ratio of line segments between anatomical markers on lateral X-ray films].

Objective: To propose a method to determine the unreasonableness of the fixed angle in posterior atlantoaxial fusion surgery based on the ratio of line segments between anatomical landmarks of the atlantoaxial joint. Methods: A cross-sectional study was conducted. According to the inclusion criteria, a screening was performed on the database of asymptomatic volunteers who had full-spine lateral X-ray films taken at the Second Affiliated Hospital of Wenzhou Medical University from May 2016 to May 2021. A total of 207 volunteers were included, comprising 98 males with an age of (40.68±13.87) years and 109 females with an age of (42.64±14.45) years. On the lateral X-ray film, a line (L) parallel to the posterior margin of the odontoid process was drawn at the posterior edge of the lower articular surface of the axis (a), intersecting the atlas at points b, c, and d. The line segments ab, bd, bc, and the C1-C2 angle were measured, and the ratios of bd/ab and bc/ab were calculated. The ability of bd/ab and bc/ab to predict the unreasonable fixed angle of the atlantoaxial joint (≥22°) was analyzed by receiver operating characteristic (ROC) curve analysis in both male and female. The areas under the ROC curves (AUC) were calculated, and the performance of the two prediction methods was compared using the Delong's test. The cutoff value for distinguishing the unreasonableness of the C1-C2 angle and the sensitivity and specificity were calculated. Results: The ROC curve analysis in the male group showed that the AUC of bc/ab for predicting the unreasonable C1-C2 angle was 0.791 (95%CI: 0.696-0.867, P<0.001), with a cutoff value of 0.449, sensitivity of 97.3%, and specificity of 70.0%. The performance was significantly better than that of bd/ab (cutoff value 1.100, AUC=0.532, 95%CI: 0.428-0.634, sensitivity 26.3%, specificity 83.3%, P<0.001). The ROC curve analysis in the female group showed that the AUC of bc/ab for predicting the unreasonable C1-C2 angle was 0.804 (95%CI: 0.745-0.852, P<0.001), with a cutoff value of 0.488, sensitivity of 90.5%, and specificity of 58.6%. The performance was significantly better than that of bd/ab (cutoff value 0.960, AUC=0.687, 95%CI: 0.624-0.748, sensitivity 90.5%, specificity 44.8%, P=0.041). Conclusions: The bc/ab value can be used as an effective indicator to predict the unreasonable C1-C2 angle in posterior atlantoaxial fusion surgery with high diagnostic accuracy. The cutoff value for males is<0.449, and for females is<0.488.

A technique to fabricate a custom CAD-CAM periapical radiographic film holder for implant assessment.

Standardized radiographs produced by using the paralleling technique play an important role in monitoring prosthetic misfit and marginal bone levels around endosseous implants. Under clinical conditions, parallel adjustment of the film with respect to the implant requires the use of positioning devices. This article describes the fabrication of a custom computer-aided design and computer-aided manufacturing (CAD-CAM) device suitable for implants adjacent to natural teeth.

Are Both Preoperative Full-Spine 3Dimensional Computed Tomography Scans and X-Ray Films Necessary for Patients with Ankylosing Spondylitis Kyphosis?

OBJECTIVE: This study is aimed to investigate whether both pre-operative full-spine 3Dimensional computed tomography scan (3D CT) and X-ray film were necessary for patients with severe ankylosing spondylitis (AS) kyphosis deformity. METHODS: The research objects were selected from the inpatients with AS in our hospital from 2017 to 2019. A total of 42 patients were included in the study. On both the synthesized 2Dimensional (2D) lateral radiograph and X-ray film, the globe kyphosis (GK), the lumber lordosis (LL), the thoracolumbar kyphosis (TLK) and the thoracic kyphosis (TK) were measured. And the angle seventh thoracic vertebra (T7), the angle twelfth thoracic vertebra (T12) and the angle third lumber vertebra (L3) were also measured. Two researchers with professional medical education were randomly selected to perform the measurement method and record the measurement data. Two researchers independently completed, recorded, and evaluated the accuracy and consistency of the measurement data. This study used intraclass correlation coefficient (ICC) to analyze the synthesized 2D lateral radiograph and general X-ray film of 42 subjects by two researchers, in order to evaluate the consistency of data measurement results between the examiners. Through the comparison of the above parameters that the GK, LL, TLK, TK, angle T7, angle T12 and angle L3, the evaluation was made both pre-operative full-spine 3D CT and X-ray film were necessary for patients with severe AS kyphosis deformity. RESULTS: There was no significant difference between the GK, LL, TLK, TK, angle T7, angle T12, angle L3 on the synthesized 2D lateral radiograph and that on X-ray film (P = 0.240, 0.324, 0.199, 0.095, 0.421, 0.087, 0.478). Agreement two researchers was excellent with ICC of the GK, LL, TLK, TK, angle T7, angle T12, angle L3 (0.977, 0.969, 0.986, 0.945, 0.947, 0.915, 0.857) on the synthesized 2D lateral radiograph. The Bland-Altman plot results that the measurement results of examiners are reliable and stable. CONCLUSION: By estimating the degree of spinal sagittal imbalance and measuring the Cobb angle, we can see that full-length spine radiographs of the patients are unnecessary for patients with severe AS kyphosis deformity who will or have undergone preoperative spine 3D CT.

Effect of scanner lens on lateral response artefact in radiochromic film dosimetry.

Radiochromic film is a good dosimeter choice for patient QA for complex treatment techniques because of its near tissue equivalency, high spatial resolution and established method of use. Commercial scanners are typically used for film dosimetry, with Epson scanners being the most common. Radiochromic film dosimetry is not straightforward having some well-defined problems which must be considered, one of the main ones being the Lateral Response Artefact (LRA) effect. Previous studies showed that the contributing factors to LRA are from the structure of the active ingredients of the film and the components and construction of the flatbed scanner. This study investigated the effect of the scanner lens on the LRA effect, as part of a wider investigation of scanner design effects and uncertainties. Gafchromic EBT3 films were irradiated with 40 × 40 cm2 field size 6 MV beams. Films were analysed using images captured by a Canon 7D camera utilising 18 mm, 50 mm and 100 mm focal length lenses compared to images scanned with a conventional Epson V700 scanner. The magnitude of the LRA was observed to be dependent on the focal length of the lens used to image the film. A substantial reduction in LRA was seen with the use of the 50 mm and 100 mm lenses, by factors of 3-5 for the 50 mm lens and 4-30 for the 100 mm lens compared to conventional desktop scanner techniques. This is expected to be from the longer focal length camera lens system being able to collect more light from distant areas compared to the scanner-based system. This provides an opportunity to design film dosimetry systems that minimise this artefact.

[A Challenge of Digitalizing the X-ray Film Image, and the Recent Technical Trends].

Fuji Photo Film (then), a chemical manufacturer that manufactures film, succeeded in digitizing X-ray photographs for the first time in the world, and commercialized Computed Radiography (CR) in 1983. In addition to eliminating darkroom work from X-ray work and improving the efficiency of X-ray work and diagnosis, this CR also played a role in paving the way for networking of image information in hospitals and for computer-added diagnostic support. Nowadays, the mechanism of digital X-rays has been established and is known to many people, but there was no precedent in the latter half of the 1970s when the development of CR was started. In this paper, we will look back on the development process of such CR first, then we will outline the evolution of digital X-ray detectors and image processing technology, and introduce the technology we have challenged to estimate scattered X-rays in the human body.

EBT3 Gafchromic® film as a new substrate for in vitro evaluation of sun protection factor.

There exist different methods for the determination of sun protection factor (SPF) values for sunscreens. We aimed to develop a new in vitro method using EBT3 Gafchromic® film as a substrate. The colour of EBT3 Gafchromic® film changes when exposed to UV light. Films were covered by sunscreen preparations of different SPF values ranging from 0 to 50. Uncovered and covered films were exposed to different solar light energies and their colour change was compared. Absorbance spectra of films was measured at 633 nm using a UV-VIS spectrophotometer apparatus. The colour of the film darkens when ultraviolet energy increases, which means that absorbance increases with exposure time. However, when films are covered by sunscreens, the colour change is less visible and the absorbance significantly decreases with increasing SPF value. There is a linear correlation between the absorbance of EBT3 Gafchromic® film and SPF value of sunscreens covering the film. Statistical analysis demonstrated that the SPF value of a sunscreen can be predicted using EBT3 Gafchromic® film as a substrate. This is the first report of an in vitro method based on colour change of a substrate which takes into consideration exposure time, and relates more closely to conditions of real-life. Based on these parameters, this is a reliable in vitro method for SPF testing.

Augmented Reality Research of Measuring X-Ray Dental Film Alveolar Bone Based on Computer Image Analysis System.

The important application of computer imaging technology in the medical field is a necessary auxiliary method for clinical diagnosis and treatment. At present, many people are affected by various factors and have various problems caused by the dental cellular bone. Traditional treatment methods are complex and long, which can cause damage to body tissues. Based on this problem, this paper takes the augmented reality measurement of X-ray dental film as the research object. Based on the in-depth measurement algorithm of the computer image analysis system, two three-dimensional reconstruction methods based on the center of gravity and the matching of the front and side positions are proposed. These two methods only need two X-rays of the front and side of the dental film, the three-dimensional parameters are obtained through calculation and analysis of each spine in the X-ray film, and these parameters are used to fit the dental alveolar bone model. The experimental results prove that the computer-based image analysis system has a great effect on the measurement of X-ray dental film alveolar bone. The positive correlation coefficient reaches 0.87. Compared with the cerebral infarction caused by other methods, the proportion of people with dental film alveolar bone injury is about 15%; after treatment, the functional recovery rate reaches more than 80%. Studies have found that there is a great difference in the age of the population that needs to be treated for dental slices and alveolar bone. The grade of patients is generally under 20 and over 60. This shows that the measurement of X-ray dental film alveolar bone based on computer image analysis system can play an important role in protecting people's oral health.

Digital radiography reject analysis of examinations with multiple rejects: an Australian emergency imaging department clinical audit.

INTRODUCTION: The largest source of manmade ionising radiation exposure to the public stems from diagnostic medical imaging examinations. Reject analysis, a form of quality assurance, was introduced to minimise repeat exposures. The purpose of this study was to analyse projection-specific reject rates and radiographic examinations with multiple rejects. METHODS: A retrospective audit of rejected radiographs was undertaken in a busy Australian metropolitan emergency digital X-ray room from March to June 2018. The data were collected by reject analysis software embedded within the X-ray unit. Reject rates, and reasons for rejection for each X-ray projection were analysed. RESULTS: Data from 11, 596 images showed overall reject rate was 10.3% and the overall multiple reject rate was 1.3%. The projections with both a high number and high percentage of rejects were antero-posterior (AP) chest (175, 18.1%), AP pelvis (78, 22.5%), horizontal beam hip (61, 33.5%) and horizontal beam knee (116, 30.5%). The projections with both a high frequency and multiple reject rate were horizontal beam knee (32, 8.4%) and horizontal beam hip (17, 9.3%). The top reasons for multiple rejects were positioning (67.1%) and anatomy cut-off (8.4%). CONCLUSIONS: The findings of this study demonstrated that projection-specific reject and multiple reject analysis in digital radiography is necessary in identifying areas for quality improvement which will reduce radiation exposure to patients. Projections that were frequently repeated in this study were horizontal beam knee and horizontal beam hip. Future research could involve re-auditing the department following the implementation of improvement strategies to reduce unnecessary radiation exposure.

THE CONCEPT OF X-RAY CT DOSE EVALUATION METHOD USING RADIOCHROMIC FILM AND FILM-FOLDING PHANTOM.

In this paper, we propose a novel radiochromic film (RCF)-based computed tomography (CT) dosimetry method, which is different from the method based on CT dose index. RCF dosimetry using Gafchromic QA2 films was performed using two lengths of film-folding phantoms. The phantom was exposed to X-ray CT through a single scan, while the RCF was sandwiched between the phantoms. We analysed the dose profile curve in two directions to investigate the dose distribution. We observed a difference in the dose distribution as the phantom size changed. Our results contradict with the results of previous studies such as Monte Carlo simulation or direct measurement. The ability to visually evaluate 2D dose distributions is an advantage of RCF dosimetry over other methods. This research investigated the ability of 2D X-ray CT dose evaluation using RCF and film-folding phantom.

Prevalence of congenital scoliosis in infants based on chest-abdomen X-ray films detected in the emergency department.

PURPOSE: To investigate the prevalence of congenital scoliosis (CS) in infants based on chest-abdomen radiographs. METHODS: A retrospective review was conducted on infants in the emergency department (ED) of a tertiary children's hospital between February 2008 and September 2019. Patients who had undergone chest-abdomen X-rays were included. All films from the enrolled patients were screened for CS. Their demographic characteristics, type, and location of the vertebral and rib anomalies, and concomitant defects of other systems were analyzed. RESULTS: In total, 50,426 infants were enrolled; 89 (1.8‰) were diagnosed with CS, including 56 males and 33 females. There was no gender difference in CS prevalence. The visiting age of the CS patients (70 ± 98days) was significantly younger than that of the non-CS group (P < 0.05), with CS patients mainly visiting for digestive (53.9%) and respiratory symptoms (41.6%). Sixty-eight (76.4%) CS patients had main thoracic (T6-T11) vertebral malformations. Rib anomalies were documented in 27 (30.3%) patients, of which 14 had complex rib anomalies. Forty (44.9%) patients had concomitant defects of other organs, of which eight patients had two systemic abnormalities mixed. The most common extraspinal defects were imperforate anus (21, 23.6%) and congenital cardiac defects (17, 19.1%). CONCLUSION: The prevalence of CS in infants based on chest-abdomen X-rays in the ED was 1.8‰. Both the vertebral and rib anomalies mainly affected the main thoracic region. The spine deformities in infants with concomitant defects of other organs could be identified earlier because of early-onset symptoms, which also bring out a selection bias in our analysis.

Radiographic modalities for diagnosis of caries in a historical perspective: from film to machine-intelligence supported systems.

Radiographic imaging for the diagnosis of caries lesions has been a supplement to clinical examination for approximately a century. Various methods, and particularly X-ray receptors, have been developed over the years, and computer systems have focused on aiding the dentist in the detection of lesions and in estimating lesion depth. The present historical review has sampled accuracy ex vivo studies and clinical studies on radiographic caries diagnosis that have compared two or more receptors for capturing the image. The epochs of film radiography, xeroradiography, digital intraoral radiography, panoramic radiography and other extraoral methods, TACT analysis, cone-beam CT and artificial intelligence systems aiding in decision-making are reviewed. The author of this review (43 years in academia) has been involved in caries research and contributed to the literature in all the mentioned epochs.

[Clinical application of distal femoral patient-specific cutting guide based on knee CT and full-length X-ray film of lower extremities].

OBJECTIVE: To discuss the feasibility and accuracy of distal femoral patient-specific cutting guide in total knee arthroplasty (TKA) based on knee CT and full-length X-ray film of lower extremities. METHODS: Between July 2016 and February 2017, 20 patients with severe knee joint osteoarthritis planned to undergo primary TKA were selected as the research object. There were 9 males and 11 females; aged 53-84 years, with an average of 69.4 years. The body mass index was 22.1-31.0 kg/m 2, with an average of 24.8 kg/m 2. The preoperative range of motion (ROM) of the knee joint was (103.0±19.4)°, the pain visual analogue scale (VAS) score was 5.4±1.3, and the American Hospital of Special Surgery (HSS) score was 58.1±11.3. Before operation, a three-dimensional model of the knee joint was constructed based on the full-length X-ray film of lower extremities and CT of the knee joint. The distal femoral patient-specific cutting guide was designed and fabricated, and the thickness of the distal femoral osteotomy was determined by digital simulation. The thickness of the internal and external condyle of the distal femur osteotomy before operation and the actual thickness of the intraoperative osteotomy were compared. The intraoperative blood loss, postoperative drainage loss, and hidden blood loss were recorded. The ROM of knee joint, VAS score, and HSS score at 3 months after operation were recorded to evaluate effectiveness. The position of the coronal and sagittal plane of the distal femoral prosthesis were assessed by comparing the femoral mechanical-anatomical angle (FMAA), anatomical lateral distal femoral angle (aLDFA), mechanical femoral tibial angle (mFTA), distal femoral flexion angle (DFFA), femoral prosthesis flexion angle (FPFA), anatomical lateral femoral component angle (aLFC), and the angle of the femoral component and femoral shaft (α angle) between pre- and post-operation. RESULTS: TKA was successfully completed with the aid of the distal femoral patient-specific cutting guide. There was no significant difference between the thickness of the internal and lateral condyle of the distal femur osteotomy before operation and the actual thickness of the intraoperative osteotomy ( P>0.05). All patients were followed up 3 months. All incisions healed by first intention, and there was no complications such as periarticular infection and deep vein thrombosis. Except for 1 patient who was not treated with tranexamic acid, the intraoperative blood loss of the rest 19 patients ranged from 30 to 150 mL, with an average of 73.2 mL; the postoperative drainage loss ranged from 20 to 500 mL, with an average of 154.5 mL; and the hidden blood loss ranged from 169.2 to 1 400.0 mL, with an average of 643.8 mL. At 3 months after operation, the ROM of the knee was (111.5±11.5)°, and there was no significant difference when compared with the preoperative one ( t=-1.962, P=0.065). The VAS score was 2.4±0.9 and HSS score was 88.2±7.5, showing significant differences when compared with the preoperative ones ( t=7.248, P=0.000; t=-11.442, P=0.000). Compared with the preoperative measurements, there was a significant difference in mFTA ( P<0.05), and there was no significant difference in aLDFA, FMAA, or DFFA; compared with the preoperative plan, there was no significant difference in FPFA, aLFC, or α angle ( P>0.05). CONCLUSION: The use of distal femoral patient-specific cutting guide based on knee CT and full-length X-ray film of lower extremity can achieve precise osteotomy, improve coronal and sagittal limb alignment, reduce intraoperative blood loss, and obtain satisfactory short-term effectiveness.

Normalized glandular dose coefficients for digital breast tomosynthesis systems with a homogeneous breast model.

This work aims at calculating and releasing tabulated values of dose conversion coefficients, DgNDBT, for mean glandular dose (MGD) estimates in digital breast tomosynthesis (DBT). The DgNDBT coefficients are proposed as unique conversion coefficients for MGD estimates, in place of dose conversion coefficients in mammography (DgNDM or c, g, s triad as proposed in worldwide quality assurance protocols) used together with the T correction factor. DgNDBT is the MGD per unit incident air kerma measured at the breast surface for a 0° projection and the entire tube load used for the scan. The dataset of polyenergetic DgNDBT coefficients was derived via a Monte Carlo software based on the Geant4 toolkit. Dose coefficients were calculated for a grid of values of breast characteristics (breast thickness in the range 20-90 mm and glandular fraction by mass of 1%, 25%, 50%, 75%, 100%) and the simulated geometries, scan protocols, irradiation geometries and typical spectral qualities replicated those of six commercial DBT systems (GE SenoClaire, Hologic Selenia Dimensions, GE Senographe Pristina, Fujifilm Amulet Innovality, Siemens Mammomat Inspiration and IMS Giotto Class). For given breast characteristics, target/filter combination, tube voltage and half value layer (HVL), two spectra with two HVL values have been simulated in order to permit MGD estimates from experimental HVL values via mathematical interpolation from tabulated values. The adopted breast model assumes homogenous composition of glandular and adipose tissues; it includes a 1.45 mm thick skin envelope in place of the 4-5 mm envelope commonly adopted in dosimetry protocols. The simulation code was validated versus AAPM Task group 195 Monte Carlo reference data sets (absolute differences not higher than 1.1%) and by comparison to relative dosimetry measurements with radiochromic film in a PMMA test object (differences within the maximum experimental uncertainty of 11%). The calculated coefficients show maximum relative deviations of -17.6% and +6.1% from those provided by the DBT dose coefficients adopted in the EUREF protocol and of 1.5%, on average, from data in the AAPM TG223 report. A spreadsheet is provided for interpolating the tabulated DgNDBT coefficients for arbitrary values of HVL, compressed breast thickness and glandular fraction, in the corresponding investigated ranges, for each DBT unit modeled in this work.

Small Animal IMRT Using 3D-Printed Compensators.

PURPOSE: Preclinical radiation replicating clinical intensity modulated radiation therapy (IMRT) techniques can provide data translatable to clinical practice. For this work, treatment plans were created for oxygen-guided dose-painting in small animals using inverse-planned IMRT. Spatially varying beam intensities were achieved using 3-dimensional (3D)-printed compensators. METHODS AND MATERIALS: Optimized beam fluence from arbitrary gantry angles was determined using a verified model of the XRAD225Cx treatment beam. Compensators were 3D-printed with varied thickness to provide desired attenuation using copper/polylactic-acid. Spatial resolution capabilities were investigated using printed test-patterns. Following American Association of Physicists in Medicine TG119, a 5-beam IMRT plan was created for a miniaturized (∼1/8th scale) C-shape target. Electron paramagnetic resonance imaging of murine tumor oxygenation guided simultaneous integrated boost (SIB) plans conformally treating tumor to a base dose (Rx1) with boost (Rx2) based on tumor oxygenation. The 3D-printed compensator intensity modulation accuracy and precision was evaluated by individually delivering each field to a phantom containing radiochromic film and subsequent per-field gamma analysis. The methodology was validated end-to-end with composite delivery (incorporating 3D-printed tungsten/polylactic-acid beam trimmers to reduce out-of-field leakage) of the oxygen-guided SIB plan to a phantom containing film and subsequent gamma analysis. RESULTS: Resolution test-patterns demonstrate practical printer resolution of ∼0.7 mm, corresponding to 1.0 mm bixels at the isocenter. The miniaturized C-shape plan provides planning target volume coverage (V95% = 95%) with organ sparing (organs at risk Dmax < 50%). The SIB plan to hypoxic tumor demonstrates the utility of this approach (hypoxic tumor V95%,Rx2 = 91.6%, normoxic tumor V95%,Rx1 = 95.7%, normal tissue V100%,Rx1 = 7.1%). The more challenging SIB plan to boost the normoxic tumor rim achieved normoxic tumor V95%,Rx2 = 90.9%, hypoxic tumor V95%,Rx1 = 62.7%, and normal tissue V100%,Rx2 = 5.3%. Average per-field gamma passing rates using 3%/1.0 mm, 3%/0.7 mm, and 3%/0.5 mm criteria were 98.8% ± 2.8%, 96.6% ± 4.1%, and 90.6% ± 5.9%, respectively. Composite delivery of the hypoxia boost plan and gamma analysis (3%/1 mm) gave passing results of 95.3% and 98.1% for the 2 measured orthogonal dose planes. CONCLUSIONS: This simple and cost-effective approach using 3D-printed compensators for small-animal IMRT provides a methodology enabling preclinical studies that can be readily translated into the clinic. The presented oxygen-guided dose-painting demonstrates that this methodology will facilitate studies driving much needed biologic personalization of radiation therapy for improvements in patient outcomes.

Detection of Radioactive DNA in Polyacrylamide Gels.

Bands of radioactive DNA separated by polyacrylamide gel electrophoresis may be detected by autoradiography or phosphorimaging. Analytical polyacrylamide gels containing radioactive DNA are usually fixed and dried before autoradiography. However, if bands of radioactive DNA are to be recovered from the gel, the gel should generally not be fixed or dried.

Autoradiography and Phosphorimaging.

Many of the commonly used techniques in molecular cloning depend on methods to map accurately the distribution of radioactive atoms on two-dimensional (2D) surfaces. Without this ability, methods such as Southern blotting, northern hybridizations, radiolabeled DNA sequencing, and library screening would not have been possible. In the 1970s and 1980s-the pioneering days of molecular cloning-imaging of 2D surfaces was obtained using autoradiography. In this technique, ß-particles emitted by radioactive specimens were recorded on X-ray film, producing a latent image that can be converted to a true image by developing and fixing the film. Autoradiography was a lot of fun, but it was also messy. In the impatient excitement of wanting to see how an experiment had turned out, people used to hold the newly developed X-ray films in their metal frames up to the darkroom light. Drips of the final wash would run down their arms, clothes would be stained, and shoes ruined. It is hardly surprising that autoradiography was quickly abandoned when sensitive phosphorimagers came onto the market at the end of the 1990s.

A clinical audit of anatomical side marker use in a pediatric medical imaging department: A quantitative and qualitative investigation.

BACKGROUND: The presence of a radiopaque or digital anatomical side marker (ASM) is an important diagnostic feature on radiographs and should be a routine feature on every radiographic image. Despite its importance, research has indicated numerous instances where ASMs were absent which have the potential to lead to adverse events. To date, few studies have systematically examined the use of ASMs in clinical practice and explored medical imaging professionals' perspectives on ASM use. This research aimed to address this knowledge gap. METHODS: This investigation was conducted in two stages. Stage 1 involved a retrospective clinical audit of 421 randomly selected radiographs within 12-months at a pediatric medical imaging department. The data were analyzed for overall presence and type of marker use. Stage 2 comprised of semi-structured interviews with 11 radiographers to garner their perspectives on ASM use, and barriers and enablers to their use in clinical practice. The interviews were transcribed verbatim and thematically analyzed. RESULTS: The overall presence of ASMs (radiopaque and digital) was observed on 99 per cent of radiographs. There was a noticeable shift towards the use of digital (78.8 per cent) compared to radiopaque ASMs (20.2 per cent), highlighting the growing trend towards using ASM in post-processing. A handful of images (N = 4) did not include any ASMs. Semi-structured interviews revealed multifaceted barriers (time, infection precautions, and patient factors) and few enablers (professionalism, legal requirement) for ASM use. CONCLUSION: This investigation, informed by quantitative and qualitative research paradigms, has shed new light on an important area of radiography practice. While missing ASMs were a small feature, there continue to remain opportunities where best practice standards can be improved. The increasing use of digital ASMs potentially highlights a shift in clinical practice standards.

[Progress on artificial intelligence assisted X-ray film recognition in orthopedics].

As an important tool for assessing musculoskeletal conditions, imaging plays an important role in assessing the risk of disease, judging disease and the progress of disease, and prognosis scores. Accompanied with the rapid development of artificial intelligence(AI) in the field of image detection and interpretation, some AI-assisted recognition studies involving musculoskeletal X-ray imaging have been examined and shown a high potential value, which can enhance various parts of the X-ray imaging value chain and guide clinicians by improving imaging efficiency, imaging quality, and diagnostic accuracy. At present, the development of AI-assisted imaging recognition technology is still at an early stage. AI algorithms need to be further improved and developed. Image data is still insufficient and the qualityis relatively heterogeneous. The long-term accuracy and stability of technical performance require further observation and research.

Radiopacity of endodontic materials using two models for conversion to millimeters of aluminum.

The aims of the present study were to compare conventional radiography, radiographs digitized with a scanner or photographic camera, and digital radiography, used to evaluate the radiopacity of endodontic materials, and to compare the accuracy of linear and quadratic models used to convert radiopacity values to equivalent millimeters of aluminum (mm Al). Specimens of AH Plus, Endofill, Biodentine and BioMTA materials (n = 8) were radiographed next to an aluminum step-wedge using radiographic films and digital radiography systems (FONA CMOS sensor, Kodak CMOS sensor and photosensitive phosphor plate-PSP). Conventional radiographs were digitized using a scanner or photographic digital camera. Digital images of all the radiographic systems were evaluated using dedicated software. Optical density units (ODU) of the specimens and the aluminum step-wedge were evaluated by a photo-densitometer (PTDM), used in conventional radiographs. The radiopacity in equivalent mm Al of the materials was determined by linear and quadratic models, and the coefficients of determination (R2) values were calculated for each model. Radiopacity of the materials ranged from -9% to 25% for digital systems and digitized radiographs, compared to the PTDM (p < 0.05). The R2 values of the quadratic model were higher than those of the linear model. In conclusion, the FONA CMOS sensor showed the lowest radiopacity variability of the methodologies used, compared with the PTDM, except for the BioMTA group (higher than PTDM). The quadratic model showed higher R2 values than the linear model, thus indicating better accuracy and possible adoption to evaluate the radiopacity of endodontic materials.